GP — 2120 tf driver installation and using document _ printing devices

Improved performance
Driver initialisation time was decreased for up to 30%.

Smaller file footprint
Driver file size was reduced for up to 60%.

We suggest that you verify existing labels and solutions before you start using this printer driver in production.

GP —

2120 tf machine with drive, from your computer without drive, plug in cable, switch on the printer, computer will popup U disk, open the driver in the U dish, driver support Windows xp, Windows 7, Windows, Windows 10, if your computer cannot find U disk, please http://www here.
gainscha。
com/ser.
Asp, download GP —
58762′

Barcode series driver, unzip the installation after the download is complete, if you want to print label, please select GP — in installation process
2120特遣部队(
The label)

, and select the USB interface, installation, as shown in the figure below:

GP —

Support 2120 tf labels and paper print mode, the machine factory default label model.

Before start printing, please make sure the printer work on what you need model, and install the correct driver.

using the tag mode, please install the driver GP —
2120特遣部队(
The label)

And load the non-drying label paper, at the same time set for label printer model.

use paper pattern, please install the driver GP —
2120特遣部队(
Notes)

And load thermal paper receipts, at the same time, the printer is set to paper pattern.

print mode switch description:

please turn it off, and hold the FEED and PAUSE two keys to boot, hear the buzzer sounded, the machine will automatically the paper and print out the current print mode, such as display paper to print bills, such as display label can print labels, repeat the above operation, you can switch between paper models and labels.

if need print label, please http://www here.
gainscha。
com/ser.

Asp download Gprinter tag editing software.

After the installation is complete, open the software design of the label size and content;

2, select printer Gprinter 2120 tf (
The label)

3, depending on the printed label size choose the length and width, column spacing is set to 0 mm, leading to label, the gap width between the average of 2 mm.

if in the use of GP —

2120 tf label printing process such as a dozen a label out a blank label, please click on the left upper corner of the editing software file, select print, will pop up a window, the diagram below:

click the printer properties to enter

click advanced Settings, and other information remains the same, there is a other advanced Settings below, the spacing between 0.
3 cm to 0.
2 cm, click close.

Цзя Бо GP-

2120 tf драйвер скачать процесс установки и использования следует обратить внимание на проблему _ печатного оборудования

bo GP —

2120 tf with the method of machine with drive, dispense with the trouble that computer without drive, plug in cable, switch on the printer, computer will pop up a U disk, open the U disk inside the built-in tag paper driver, can support the Windows xp, Windows 7, Windows, if can’t find U disk on your computer, please download it here: http://www.
gainscha。
cn/cn/download。
aspx吗?

Current = down, the first software download center name: bar code printer driver, bar code editing software, please click on the tool, download NiceLabel for Gprinter tag editing software, click download below to save small yellow triangle can be downloaded to your computer;

After the download is complete, please click on the extract driver installation, if you want to print labels, during the installation process GP — please be sure to choose better
2120特遣部队(
The label)

, and select the USB interface, installation, as shown in the figure below:

bo GP —

2120 tf have two modes, label and its function, we machine factory default label model, but if you are in the process of using the machine without positioning or an error, please be sure to confirm whether the machine is required for your current mode, if you are to put the non-drying label paper, please be sure to adjust the machine to tag mode, if the current for the paper pattern, the machine could not go paper or paper positioning;

If you are to print bills, installed jia bo GP —
2120TF(
Notes)

And be able to print the test page, machine for paper pattern at the same time, be sure to put paper receipts, otherwise the correct machine will flash a red light.

How to switch machine mode below:

if you have questions, please check carefully jia bo GP —
Tf 2120 specifications.

after the above operations, if you want to print labels you need, please install: NiceLabel for Gprinter tag editing software, after the installation is complete, click on the icon to open the software, to create a new TAB, and enter your tags to determine the specifications of the length and width, click next after can edit you want to print the contents of the, as shown in the figure below:

if you have a label template, and specifications, and your paper can be used directly, if inconsistent can double-click on label the margin Settings label format, above operation basically can fulfill the task of printing label, if there are other problems in the printing process, you can directly contact you buy businesses, provide technical support for you.

click advanced Settings, and other information remains the same, have a other advanced Settings below, the spacing between 0.
3 cm to 0.
2 cm, click close.

warm prompt: if there are other problems in use process, also can contact our manufacturer directly, I wish you a happy work, good printing, print in the future.

Про мини ПК:  Какие этикетки нужны для wildberries?... Размеры штрихкодов и наклеек WildBerry
Оцените статью
Карман PC
Добавить комментарий